TL;DR: Payment Terminal Board Custom Logo
About AndroidSBC and the Smart Payment Terminal Android Motherboard Family
Wanlin Manufacturing Group runs the smart payment terminal board programme out of Longgang in Shenzhen, where the twelve WF-SPT configurations are assembled, burned in and packed with their compliance documents. For international market and international market importers the practical result is a single bill of materials per production lot and one qualification file per configuration. Peripheral validation is treated as part of the product, not as an afterthought: the printer header pinout, the reader antenna keep-out and the scan engine UART mapping are fixed at the design stage and held for the life of the configuration in international market.
WF-SPT-05 Technical Specifications
| Parameter | AndroidSBC WF-SPT-05 (dual-screen smart payment terminal build for chain checkout) | Industry Average |
|---|---|---|
| Processor | RK3576 quad-core ARM Cortex-A72 2.2GHz plus quad-core ARM Cortex-A53 1.8GHz SoC | Older dual-core or quad-core Cortex-A7 SoC |
| Process node | 8nm | Older 40nm process |
| GPU | Mali-G52 MC3 | Older Mali-400 or basic 2D GPU |
| Memory | 8GB LPDDR5 | DDR3 512MB or 1GB on competing boards |
| Storage | 128GB eMMC plus TF card up to 256GB | NAND flash 4GB or 8GB on competing boards |
| Display and touch | 8-inch 1280x800 eDP main panel plus 4-inch customer screen with 10-point capacitive touch with glove and wet-finger support | 4.3-inch 480x800 panel with resistive touch |
| Payment and capture | NFC contactless, IC card, magnetic stripe and QR with secure element | Camera-only QR capture with no scan engine |
| Printer and peripherals | 80mm thermal printer header with 180mm per second output | No printer control header on competing boards |
| Wireless and positioning | dual-band WiFi 6 with Bluetooth 5.4 and optional 5G sub-6 modem | Single-band 2.4G WiFi 802.11n with no modem |
| Interfaces | 1 USB Type-C host and OTG, 2 USB host, 1 RS232, 1 HDMI out, 8 GPIO, 1 thermal printer header | One USB port and no RS232 |
| Operating system | Android 14 with AOSP baseline and optional GMS | Android 9 or Android 10 on competing boards |
| Power and reliability | 12V DC input with 5V/3A peripheral rail, dual-cell RTC and watchdog, -20C to 60C operating ambient | No battery management and no watchdog |
All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-SPT-05 (dual-screen smart payment terminal build for chain checkout) holds the touch panel, the thermal printer, the reader and the scan engine together while running the 72-hour burn-in loop, a configuration that competing single-platform boards rarely document at the top of the temperature window. For international market importers sourcing the WF-SPT family, the WF-SPT-05-A variant is the typical configuration for the hypermarket and supermarket chain checkout lanes use case, in a payment terminal footprint with a sustained weekly capacity of 5000 pcs/wk.
Challenges in Sourcing Smart Payment Terminal Android Motherboards for international market Buyers
The first problem international market buyers hit is the difference between a sample that works and a configuration that repeats. A board can pass a bench test and still fail in volume if the printer driver, the scan engine mapping and the modem band list were never documented as part of the delivery.
Certification is not a one-time event in international market. When the acquiring partner updates a kernel version or a contactless limit, the international market integrator needs a board supplier who can reissue the file rather than renegotiate the design. What international market integrators get is a board that repeats: 199100 units now, 199100 more next quarter, the same connector map, the same printer pinout, the same Android baseline, all moving on the international market - Shenzhen lane into international market.
Competitive Comparison: WF-SPT-05 vs Competing Smart Payment Terminal Motherboards
A international market integrator comparing two boards should compare the delivery file, not the datasheet. One side ships a test report and a compliance set; the other ships a board and a promise.
- vs consumer tablet boards: the WF-SPT family carries a printer control header, a reader antenna reference design and a scan engine UART mapping, none of which exist on a tablet derivative board.
- vs single-configuration boards: twelve configurations share one peripheral contract, so a international market buyer can move from a countertop lane to an unattended kiosk without re-qualifying the printer or the reader.
- vs boards without a firmware plan: signed images, staged OTA groups with rollback and a published maintenance window come standard, where competing boards ship an image and leave the international market integrator to manage it.
- vs re-spun designs: the bill of materials is frozen per production lot for the length of the agreement, so the board that passed qualification in international market is the board that ships in volume.
Global Cashless Payment, Smart Terminal and Self-Service Checkout Market Trends
Market growth in international market is concentrating in the formats where a human is not present at the moment of payment, which puts the watchdog, the modem band list and the offline buffer at the top of the international market specification.
- Countertop tier: WF-SPT-12 covers contactless, IC card, QR and receipt printing in one board, which is the configuration most staffed lanes standardise on.
- Unattended tier: WF-SPT-09 pairs the modem with the printer header and the watchdog for vending, lockers and kiosks where nobody is there to reboot the terminal.
- Flagship tier: WF-SPT-04 adds the larger memory and storage bundle, the customer-facing screen option and the wider temperature window that outdoor and high-throughput formats require.
The international market market is large enough to absorb several suppliers and disciplined enough to punish the ones who re-spin boards between lots. Holding the configuration is the strategy, and it is the one AndroidSBC runs for international market.
WF-SPT-05 Application Scenarios
The WF-SPT-05 dual-screen smart payment terminal build for chain checkout sits inside a twelve-configuration WF-SPT Android motherboard family from AndroidSBC, a Wanlin Manufacturing Group export brand. The WF-SPT-05-A configuration is the typical build for the hypermarket and supermarket chain checkout lanes use case, with printer current profile, scan engine mapping and staged OTA management bundled.
- Convenience and grocery counters: the WF-SPT-07 takes contactless, IC card and QR at the till and prints the receipt in one pass.
- Restaurant and quick-service counters: the WF-SPT-04 runs order entry, payment and kitchen ticket printing on the same board.
- Unattended vending and lockers: the WF-SPT-08 pairs the modem with the printer header and the watchdog for sites with no staff present.
- EV charging and fuel forecourts: the WF-SPT-09 holds the wide input range and the sunlight readable panel through a full outdoor season.
- Transit gates and event entry: the WF-SPT-08 takes contactless payment and prints the entry ticket without a fixed counter.
- Self-checkout lanes: one board drives the main panel, the scanner and the receipt printer, with the customer screen option where the format needs it.
- Hotel and resort reception: card pre-authorisation, signature capture and folio printing on a board that also runs the restaurant terminal.
- Hospital and clinic payment desks: card, QR and insurance capture on a locked-down build with staged OTA and an audit trail.
- Government and municipal counters: tax, permit and fee payment on a configuration held for the length of the agreement.
Partnership Models for international market Buyers
The international market decision is usually commercial rather than technical - whether the partner wants inventory risk, integration depth or brand ownership in international market.
- Distribution track: the partner buys the WF-SPT board against a published price list, keeps its own stock, and AndroidSBC supplies the printer profile, the scan mapping and the compliance documents with each lot.
- Integration track: the partner takes the board plus firmware customisation, receipt and language localisation and peripheral validation support, with a joint qualification run at the Longgang factory.
- Private-label track: the WF-SPT board ships under the partner brand with customised boot logo, packaging, enclosure and documentation, on a fixed bill of materials held for the length of the agreement.
The international market partner that starts on the distribution track and moves to private label does not re-qualify the board, which is the point of holding one peripheral contract across the family.
Frequently Asked Questions
Does the smart payment terminal board family support a dual-screen payment terminal build for chain checkout?
Answer: Yes. The dual-screen payment terminal build for chain checkout is one of the twelve held configurations, which means the bill of materials is frozen for the length of the agreement rather than re-spun between lots in international market.
Which configurations are available in the WF-SPT family for international market buyers?
Answer: AndroidSBC ships twelve configurations including the RK3576 board: value desktop, 4G unattended, face recognition, dual-screen, kiosk, legacy Android 11, portable 4G, outdoor, hospitality, multimedia and legacy Linux builds.
Can one smart payment terminal board drive a touch panel, a thermal printer and a scan engine at once?
Answer: Yes. AndroidSBC validates the panel, the printer and the scan engine together rather than separately, because the combined current draw is what decides whether a terminal survives a shift in international market.
What payment scheme certification support does AndroidSBC provide for international market?
Answer: AndroidSBC prepares IMDA type approval with Spring international market conformity documentation and IMDA conformity files alongside the production order, so the international market acquiring partner receives a file that names the parts on the pallet.
What is the minimum order quantity and the sample lead time for international market?
Answer: For international market programmes the practical answer is a sample lot first, a joint qualification run second, and a production slot third, with the compliance file issued at the sample stage.
Is custom ROM, boot logo or pre-installed app development available?
Answer: Yes. Boot logo, custom launcher, kiosk mode and pre-installed applications are all available, delivered as a signed image with a staged OTA plan for the international market estate.
How are firmware updates delivered to a international market device estate after deployment?
Answer: Updates are signed, staged and reversible. The international market integrator chooses the group size, and a failed update returns the terminal to the previous image without a site visit.
What shipping terms does AndroidSBC support for international market orders?
Answer: Terms are agreed per programme: FOB Shenzhen for stock configurations, CIF Port of international market for volume lots, and DAP where the international market partner wants delivery to its own warehouse.
Contact AndroidSBC: Start Your WF-SPT-05 Sourcing Conversation
For international market buyers the fastest route is a sample lot: specify the format, order the board, qualify it on the bench, then move to a production slot with the compliance file already prepared.
- Email: Androidsbc@163.com
- Export service hotline: +8613261677119
- Website: https://www.androidsbc.com
- Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China
For international market and international market buyers the offer is a source-factory relationship: twelve configurations, one peripheral contract, a frozen bill of materials and a compliance file that ships with the pallet rather than after it.
